What is the R-value of Neopor?
5 per 1-1/
Thermal Resistance: R-value of 5 per 1-1/16 inch (27 mm) at 75 degrees F (24 degrees C) mean temperature. 8. Manufacturers: a. BASF Corporation; BASF Neopor Plus GPS: www.neopor-basf.com.
What is Neopor insulation?
BASF Neopor® GPS is a graphite polystyrene (GPS) rigid foam insulation that gives maximum efficiency, cost-effectiveness and sustainability on construction projects. The graphite reflects radiant heat energy like a mirror, increasing the material’s resistance to the flow of heat, or R-value.
Who makes the GPS insulation?
BASF
Graphite polystyrene insulation, or GPS, is made from Neopor beads, patented and manufactured by BASF. Neopor gives GPS insulation a dark gray appearance and higher r-value than traditional EPS insulation products.
What is InsulFoam made of?
InsulFoam FL (Flute-Filler) is a custom-made, engineered insulation consisting of a superior closed-cell, lightweight expanded polystyrene (EPS).
What is graphite foam?
Graphite foams were prepared from a coal tar pitch that was partially converted into mesophase. Expandable graphite was used instead of an inert gas to “foam” the pitch. % expandable graphite had a bulk density of 0.249 g cm−3, a compressive strength of 0.46 MPa and a thermal conductivity of 21 W m−1 K−1.
What is the R-value of 2 inch polystyrene?
A wall utilizing STYROFOAM T-MASS Technology with a 2-inch exterior layer and a 4-inch interior layer of concrete along with a 2-inch layer of STYROFOAM extruded polystyrene insulation would result in a material R-value of approximately 11.33.
Which is better XPS or EPS?
When tested through this method, XPS is seen as the more resistant option, because it resists water absorption more than EPS. But, at the same time, while it takes in moisture at a slower rate, it also releases it more slowly. Meaning, any moisture that gets retained is present longer in XPS insulation.
What is the R value of InsulFoam?
about 3.9 per inch
InsulFoam EPS has R-values that vary depending on temperature and the density of the product installed. For instance, our standard R-TECH, sold in home improvement stores, has an average R-value of about 3.9 per inch at 75°F.
Is InsulFoam waterproof?
The plastic film on Insulfoam sheets does not serve as waterproofing however. For true waterproofing and insulation in a single product, several companies offer underslab products that combine a flexible EPS core with two layers of vapor and moisture resistant materials.
How strong is polystyrene?
What are the properties of PS?
| Property | Value |
|---|---|
| Tensile Strength | 53 MPa (7700 PSI) *** |
| Flexural Strength | 83 MPa (12000 PSI) *** |
| Specific Gravity | 1.04 |
| Shrink Rate | 0.3 – 0.7 % (.003 – .007 in/in) *** |
Can you paint polystyrene?
You can paint polystyrene foam or expanded polystyrene beads using a waterborne paint to protect it from solvent attack by subsequent coats of paint. After the polystyrene is completely covered, you can over-coat it using a conventional paint, if need be.
What kind of machine is the Neopost in-600?
Neopost IN-600 Franking Machine. The Neopost IN-600 Franking Machine is their only mid-volume model for businesses with moderate mailing needs. It’s a step-up from the IN-360 but not quite as powerful as the IN-700.
Which is best Neopor or Neopor GPS insulation?
And, Neopor GPS is stable as it consistently delivers the highest true R-value performance over time. Neopor GPS is a breathable and semi-permeable high performance insulation that helps reduce the risk of mold, rot and structural damage associated with moisture condensation and long-term water retention.
How is graphite used to make Neopor GPS?
Silver-Grey Neopor GPS is comprised of many small pockets of air within a polymer matrix containing graphite. The graphite reflects radiant heat energy like a mirror, increasing the material’s resistance to the flow of heat, or R-value. Most polymer-based foams exhibit a greater ability to slow the movement of heat as the temperature decreases.
What kind of insulation does BASF Neopor use?
BASF Neopor ® GPS is a graphite polystyrene (GPS) rigid foam insulation that gives maximum efficiency, cost-effectiveness and sustainability on construction projects. Planners, architects, contractors and builder-owners benefit from insulation made of Neopor GPS because of the special advantages this material offers.